INTERP_KERNEL Namespace Reference

Classes
class	ArcCArcCIntersector
class	ArcCSegIntersector
class	ComposedEdge
class	CrossTypeEdgeIntersector
class	Edge
class	EdgeArcCircle
class	EdgeIntersector
class	EdgeLin
class	ElementaryEdge
class	Interpolation
class	Interpolation2D
class	Interpolation3D
class	Interpolation3DSurf
class	InterpolationOptions
class	IntersectElement
class	IteratorOnComposedEdge
class	MergePoints
class	Node
class	PlanarIntersector
class	QuadraticPolygon
class	SameTypeEdgeIntersector
class	SegSegIntersector
class	TargetIntersector

Enumerations
enum	IntersectionType {   Triangulation, Convex, Geometric2D, PointLocator,   Barycentric, BarycentricGeo2D, MappedBarycentric }
enum	NormalizedCellType {   NORM_POINT1 = 0, NORM_SEG2 = 1, NORM_SEG3 = 2, NORM_SEG4 = 10,   NORM_POLYL = 33, NORM_TRI3 = 3, NORM_QUAD4 = 4, NORM_POLYGON = 5,   NORM_TRI6 = 6, NORM_TRI7 = 7, NORM_QUAD8 = 8, NORM_QUAD9 = 9,   NORM_QPOLYG = 32, NORM_TETRA4 = 14, NORM_PYRA5 = 15, NORM_PENTA6 = 16,   NORM_HEXA8 = 18, NORM_TETRA10 = 20, NORM_HEXGP12 = 22, NORM_PYRA13 = 23,   NORM_PENTA15 = 25, NORM_HEXA20 = 30, NORM_HEXA27 = 27, NORM_POLYHED = 31,   NORM_ERROR = 40, NORM_MAXTYPE = 33 }
enum	NumberingPolicy { ALL_C_MODE, ALL_FORTRAN_MODE }
enum	SplittingPolicy { PLANAR_FACE_5 = 5, PLANAR_FACE_6 = 6, GENERAL_24 = 24, GENERAL_48 = 48 }
enum	TypeOfEdgeLocInPolygon { FULL_IN_1 = 1, FULL_ON_1 = 4, FULL_OUT_1 = 2, FULL_UNKNOWN = 3 }
enum	TypeOfFunction { SEG = 1, ARC_CIRCLE = 4, ARC_PARABOL = 8 }
enum	TypeOfLocInEdge {   START = 5, END = 1, INSIDE = 2, OUT_BEFORE = 3,   OUT_AFTER = 4 }
enum	TypeOfLocInPolygon {   IN_1 = 7, ON_1 = 8, ON_LIM_1 = 12, ON_TANG_1 = 9,   OUT_1 = 10, UNKNOWN = 11 }
enum	TypeOfMod4QuadEdge { CIRCLE = 0, PARABOL = 1 }

Variables
const unsigned	MAX_SIZE_OF_LINE_XFIG_FILE =1024

Enumeration Type Documentation

enum INTERP_KERNEL::NormalizedCellType

Enumerator
NORM_POINT1
NORM_SEG2
NORM_SEG3
NORM_SEG4
NORM_POLYL
NORM_TRI3
NORM_QUAD4
NORM_POLYGON
NORM_TRI6
NORM_TRI7
NORM_QUAD8
NORM_QUAD9
NORM_QPOLYG
NORM_TETRA4
NORM_PYRA5
NORM_PENTA6
NORM_HEXA8
NORM_TETRA10
NORM_HEXGP12
NORM_PYRA13
NORM_PENTA15
NORM_HEXA20
NORM_HEXA27
NORM_POLYHED
NORM_ERROR
NORM_MAXTYPE

enum INTERP_KERNEL::SplittingPolicy

Type describing the different ways in which the hexahedron can be split into tetrahedra. The PLANAR_* policies persume that each face is to be considered planar, while the general policies make no such hypothesis. The integer at the end gives the number of tetrahedra that result from the split.

The images below illustrates the policies in their respective order.

Enumerator
PLANAR_FACE_5
PLANAR_FACE_6
GENERAL_24
GENERAL_48

enum INTERP_KERNEL::NumberingPolicy

Enumerator
ALL_C_MODE
ALL_FORTRAN_MODE

enum INTERP_KERNEL::TypeOfFunction

Enumerator
SEG
ARC_CIRCLE
ARC_PARABOL

enum INTERP_KERNEL::TypeOfMod4QuadEdge

Enumerator
CIRCLE
PARABOL

enum INTERP_KERNEL::TypeOfLocInEdge

Enumerator
START
END
INSIDE
OUT_BEFORE
OUT_AFTER

enum INTERP_KERNEL::TypeOfEdgeLocInPolygon

Enumerator
FULL_IN_1
FULL_ON_1
FULL_OUT_1
FULL_UNKNOWN

enum INTERP_KERNEL::TypeOfLocInPolygon

Enumerator
IN_1
ON_1
ON_LIM_1
ON_TANG_1
OUT_1
UNKNOWN

enum INTERP_KERNEL::IntersectionType

Enumerator
Triangulation
Convex
Geometric2D
PointLocator
Barycentric
BarycentricGeo2D
MappedBarycentric

Variable Documentation

const unsigned INTERP_KERNEL::MAX_SIZE_OF_LINE_XFIG_FILE =1024

Referenced by INTERP_KERNEL::EdgeLin::EdgeLin(), and INTERP_KERNEL::QuadraticPolygon::QuadraticPolygon().